Photographs in Different Colors
PROCESSES for changing ordinary black prints on Velox and like developing papers to fine browns, bright reds, and bright blues and greens are just now attracting a great deal of attention among photographers, who desire to secure the very best results in their pictures, and who find that many subjects are not entirely satisfactory in plain black and white. Often marines are better in blue, and harvest-fields in brown, broad meadows and woods in green, and cosy, firelit rooms in red. Thus a great many subjects can be shown to the best possible advantage only by careful and judicious choice of the color in which they are made.
For all colors the foundation is laid by making first a common black and white picture on developing paper, and washing it very thoroughly. Such a picture is then ready for treatment with the chemical solutions that are to change its color.
Brown or sepia is the color having, next to black, the widest range of usefulness. It is also the color which, next to black, is most easily and surely produced. All dealers sell the “sepia redevelopers” ready prepared, and it is far better to buy them ready prepared than to attempt their compounding one’s self. Each package contains two sets of chemicals: one set is to be dissolved in water, and the picture immersed in the resulting solution until it has been all bleached out. It is then rinsed and immersed in the other solution, which quickly redevelops it into a strong and beautiful brown—hence the name “redeveloper.” The whole operation takes but three or four minutes, is very simple, and full directions accompany each package.
Pictures in blue also can be produced by the use of a ready-prepared set of chemicals, which is sold by a number of supply houses in this country. If, however, one can not find it at the stores, he can make up the solution as follows: Into a glass measure pour ¼ ounce of a ten-per-cent solution of ammonia-citrate of iron; add to this ¼ ounce of a ten-per-cent solution of potassium ferricyanid (red prussiate of potash); next pour in ½ ounce of a ten-per-cent solution of nitric acid; and finally add 5 ounces of water.
In this bath the black print quickly changes color, first becoming blue black, then bluer and bluer, until in a minute it has assumed a deep Prussian blue. When the desired tone has appeared, the picture is transferred to clean water, and washed for a long time to perfectly clear away any blue stains that may have appeared in the white parts of the picture. When the whites are clear the print may be dried and mounted in the usual manner.
Red pictures are just as easily made as blue ones. Prepare two solutions: A. Water ½ ounce; 15 drops of a ten-per-cent solution of copper sulphate (blue vitrol); of a ten-per-cent solution ammonium carbonate (enough to re-dissolve the precipitate first formed) about ¼ ounce. This solution should be a clear, bright blue. For solution B. take ¾ ounce of a ten-per-cent solution potassium ferricyanid (red prussiate of potash) and 4½ ounces of water.
Add B to A and shake well; a muddy liquid will be produced which will quickly tone black prints to a beautiful red, or, with 5 ounces more water added, it will give purple tones if the print remains in it but a short time. The tendency of this solution is to slightly stain the whites of the picture, and as yet no satisfactory way of removing the stain has been discovered. However, the stain is generally very slight, and does not in the least mar the beauty of the picture.
About the best way of getting a good green color is to first tone the picture a rich blue, wash it until the whites are pure and clear, and then tone the blue picture in a yellow toning bath. The yellow-producing solution will produce a yellow tone which will combine with the blue to make a fine green. The yellow solution is made as follows: Dissolve 1 dram of bichlorid of mercury (a poison) in 7 ounces of water, and 3 drams of iodid of potassium in 3 ounces of water; pour the iodid solution into the mercury solution till the red precipitate first formed is completely dissolved. A black print immersed in this solution for a minute or so and then washed, changes to a bright yellow, while a blue-toned picture immersed in it and then washed becomes a strong rich green. The solution can be returned to its bottle, and used over and over many times.
The Why of Failure—The Little Things
Since the first of these articles appeared, many of the INSTRUCTOR readers have sent me questions relating to things photographic, and some have enclosed prints and film negatives in their letters, asking me the causes of their non-success. In nearly every case I have been obliged to tell these beginners that their trouble lies in a disregard for the “little things.” Some seeming trifle is overlooked, and lo, a picture results that can only cast discredit on its maker!
Just the other day I received a lot of prints that were stained a muddy yellow. “What can be the matter of the paper,” asked the sender, and I told him that he had forgotten to “fix” it, after developing. Some of the newer developers, as you know, do stain the picture yellow, and the yellowness can be removed only by a thorough fixing. He, however, had wholly overlooked the little important matter of fixing; and judging from some of the faded and stained prints I receive, I think there are other of my readers also who consider thorough fixing and subsequent washing of rather small importance. Stained and faded pictures are bound to be the result of all such disregard of the positive instruction to “fix well, and wash thoroughly.”
It is just so in the matter of plates and films, the chief trouble being incorrect exposure, and a bad red light in the dark room. Many and many a fogged negative, good for nothing but the ash barrel, would be as good as any, had its maker developed it by a proper light. But there are spotted negatives, and fogged negatives, and scratched ones, and frilled ones, and spoiled ones of every kind, just because of some such unnecessary carelessness—some little disregard of detail. I can not here point out all these causes of failure, for there is a multitude of them; but I do want to just suggest to those who make these failures that when they make them, they should each time go back in their minds over each detail of their work, and trace out for themselves that “little important thing” wherein they have blundered. Thus they will soon become more careful of every phase of their work, and better success will surely crown their efforts.
Important Questions
Do you keep your camera free from dust and its lens perfectly clean?
Are you sure there is not a tiny crack or pinhole somewhere in the camera, that leaks light?
Do you wash out your developing trays each time after using?
Is your dark room really dark?
Are you careful to shield your plates and films as much as possible, even from red light while developing them?
Do you weigh and measure your chemicals accurately according to directions, or do you sometimes simply “guess”?
Do you stay with one make of paper or plate or developer until you have learned fully how to use it, or do you try first one and then another and have small success with any?
In beginning the development of a plate have you learned how to pour on the developer to instantly cover the entire surface, without leaving any spots uncovered?
Are you careful to handle all plates and papers by the edges so as not to leave finger-marks on the delicate surfaces?
How to Make Large Developing Trays
One of our readers who is making some bromid enlargements says he has trouble in getting trays large enough in which to develop, fix, and wash his big pictures, and asks if a satisfactory tray can not be made at home.
There are several ways of making good trays, the simplest and easiest made being a large shallow wood box, rendered waterproof in some way. It can be rendered waterproof by coating the inside thoroughly with very hot melted parafin wax, or by painting it with several coats of a special chemical-proof paint that is sold by photo dealers for the purpose, or the box can be lined with oilcloth. In lining with oilcloth I have found the following construction best: The sides are nailed to the bottoms first, the oilcloth is fitted in and tacked along the top of the sides, the ends of the oilcloth are then bent up into shape with the “ears” or doubles at the corners pointing outward (not inside the tray); the ends are then nailed in place, thus fastening the ears between sidepieces and ends and leaving the inside of the tray, even the corners, free from all wrinkles or folds. EDISON J. DRIVER.
NOTE.— As the making up of the foregoing chemical solutions is somewhat troublesome, and the chemicals to be obtained in drug-stores are often unreliable, some of my readers may wish to buy the preparations ready for use, and not know where to get them. If any such person will send me a self-addressed stamped envelope or a postal card, I will give him the addresses desired. However, the yellow producing solution will have to be compounded by the user, as it is not, so far as I know, for sale in this country.