AdventAI

LANTERN-SLIDES

By J. Edgar Ross

From The Youth’s Instructor, Vol. 48, No. 30., July 26, 1900

The “magic” lantern has long been a valuable aid to the lecturer in bringing before an audience pictures illustrating his subject. But the term “magic lantern” is a misnomer. There is nothing magical about the apparatus. A sixteen-year-old boy possessing any mechanical ability, can, with a little study and a good deal of patient labor, make a magic lantern, even to grinding the lenses. The instruments are also often miscalled stereopticons; but the word is unwieldy, even if it were allowable. In common parlance the word “magic” is dropped from the old name, and the instruments are called simply “lanterns.” But the lantern itself is foreign to the subject of photography, so I must confine this paper to instruction for making the slides.

Three and one-fourth by four is the standard size of lantern-slides, and all but the toy instruments are made to use that size. Excellent slides may often be made with common dry-plates; but the special lantern-slide plates are much better, and should be used whenever possible. These plates, being slower than the common ones, admit of greater latitude of exposure.

If negatives of the exact size are to be used to make the slides, you will not need a camera. The plate and negative may be placed in contact in the printing-frame, and the printing be done by artificial light, just as you would handle bromide paper. Some photographers use the camera in making slides, even when the size is not to be changed; but I prefer to print by contact whenever possible.

If the camera is three and one-fourth by four and one-fourth, you may succeed in making the plates stay in the holder without a kit; but if it is four by five or larger, you must either buy or make one. They are usually made of wood, but thick cardboard will do just as well, and will be much easier to make.

Before using plates smaller than your ground-glass, whether in making negatives or lantern-slides, it is well to mark your ground-glass so that you can see at a glance what part of the image will fall on the plate when it is in position. To do this, lay a plate of the size you intend to use in the proper position on the ground side of the glass, and trace around it with a lead-pencil. These marks will not interfere with the focusing when using a larger plate; but if you desire to remove them, they may be wiped off with a damp cloth.

Take a board about eighteen inches wide, and as long as the width of the north window chosen for your work, and in the center of it cut an opening somewhat smaller than the negatives from which you are going to make the slides. Cover this opening on one side of the board with ground-glass or white tissue-paper. If the former is used, it may be fastened in position with tacks; if the latter, it should be pasted on.

Stand this board on edge on the window-sill, with the covered side of the opening outward, and fasten it there in any convenient way. Drive two tacks at the bottom, and one at each side, of the opening. They should be so close to the edge of the opening that the negative will just slip in between them, and be held in position by the tack-heads.

Draw down the shade till it covers the top of the board; and if there is another window in the room, draw the shade of that window also; so all the direct light entering the room will come through the opening in the board and the negative that covers it.

Now you are ready to begin work; and a number of slides may be made from different negatives almost as easily as one.

Place your camera on the tripod in front of the negative, and adjust the size by moving it back and forth, and the height by moving it up and down. Do not tilt the camera, as it will give a distorted image. Be sure to get an accurate focus. If you have one, a reading-glass will be a great help in this.

The exposure of lantern-slides will vary under different circumstances just as will the exposure of plates and bromide paper. With a fair light and a negative of moderate intensity, fifteen seconds will be a safe time on which to make the first test.

Lantern-slides require concentrated developer, strongly restrained. Otherwise the development and subsequent treatment are similar to other dry-plates. Our “standard” developer, diluted with an equal part of water, is excellent. With the addition of six drops of a ten-per-cent solution of bromide of potash to each ounce of the mixed developer, it will usually be sufficiently restrained to keep the high lights clear.

Do not overdevelop. When all the detail is out, the slide is ready for the fixing-bath.

When the plate is dry, the film side is furnished with a mat of appropriate size and shape, and then covered with a plain glass, to protect it from scratches. The plate and cover are then bound together with strips of adhesive paper, and the slide is ready for exhibition in the lantern. J. EDGAR ROSS.