AdventAI

ELEMENTARY PHOTOGRAPHY

By J. Edgar Ross

From The Youth’s Instructor, Vol. 48, No. 21., May 24, 1900

CONTACT PRINTING WITH BROMIDE PAPER

Bromide paper is coated with an emulsion similar to that used in the manufacture of dry-plates. It is not nearly so sensitive as an ordinary plate, but the sensitiveness of different makes varies greatly. “Standard” bromide paper is about one twentieth as sensitive as a “Seed’s 26x” plate. It is especially adapted to the making of enlargements, but within the last few years it has been extensively used in making contact prints.

There are now a considerable number of bromide papers that are made especially for contact printing. They are not usually called “bromide” papers, but are known by some trade name. Of this class Velox is the pioneer, and still holds the lead; but there are others just as good, and one, Vinco, that is sold at a much lower price.

The natural tone of bromide paper is black. It may be varied somewhat by different treatment, either during or after development; but with the majority of pictures the black tone gives the most satisfactory results.

The standard bromide paper must be handled in the dark-room, though it will bear light that would hopelessly fog a dry-plate. Both sides of the paper will look alike; but the film side will curl in, so there will be no difficulty in distinguishing between them.

Artificial light is best for printing. If daylight is used, there will be great danger of over-exposure, and it will be almost impossible to make uniform exposures. The time will depend upon the density of the negative and the intensity of the light. A negative of moderate density, held one foot from a number two kerosene burner, should print in about twelve seconds. It is quite difficult to count seconds accurately; but by practicing by the second-hand of a clock or watch, the knack may be acquired. A pendulum thirty-nine or forty inches long will beat seconds very nearly. The exact length required varies with the latitude, but this is near enough for all practical purposes.

If your lantern is made according to the plan suggested in one of the articles of this series, it will be just the thing to print bromide paper by. Place the printing-frame where the light of your lamp will fall upon it when the sliding door of the lantern is raised. When the necessary time has passed, the light can be instantly shut off by sliding the door into place again. The paper may then be removed from the frame, and developed.

The manufacturers of bromide paper usually recommend an iron developer. But iron is very difficult for a novice to handle. When properly and successfully used, it gives beautiful results; otherwise it gives complete failures. Almost any developer, except pyro., may be used with more uniform success than iron. But for beautiful, “snappy” prints, with shadows that are black, and high lights that are white, our standard developer, diluted with two parts of water, can not be improved. The development is carried on just as with a plate, except that the print must be examined by reflected instead of transmitted light. After development, the print is immersed for ten minutes in a fixing-bath made by dissolving one ounce of hypo. in five ounces of water. Now wash the prints through twelve changes of water, allowing them to soak five minutes in each, or wash one hour in running water. Then they may be mounted or dried just like print-out paper.

Unmounted prints usually curl badly in drying. They may be straightened by scraping the back with a rule, the corner of the print being lifted behind the ruler as it passes along.

Over-timed prints will have greenish-black shadows and stained high lights. If they are under-timed, the shadows will be gray instead of black, and the half-tones will be very weak. Pin-holes may usually be spotted out with a lead-pencil. Over-developed prints may be reduced in the same manner that negatives are; but it is best to use a weaker bath, to guard against over-reduction. Sometimes failures will occur from other causes than those mentioned; but it is usually better to throw away the print and make another, than to attempt to doctor it.

For many subjects bromide paper may be substituted for dry-plates in making the negative. As it is sold at about one third of the price of dry-plates, the economy of its use is apparent. The necessary exposure will be about fifteen or twenty times as long as the time required by a first-class dry-plate. The paper negative is developed, fixed, and washed in the ordinary manner. It must of course be dried unmounted. When dry, it is immersed in melted paraffin wax to hide the grain of the paper, and make it translucent, so that it will print more rapidly. It may then be hung in a warm place until the surplus wax drips from it, when it will be ready for the printing-frame.

Bromide paper can not be successfully used in portraiture; but for landscapes and architectural subjects it is in many cases quite as good as dry-plates. J. EDGAR ROSS.