Many of the mistakes made by beginners in photography are fatal; but some can, in a measure, be corrected. Of course it is best to avoid mistakes; and if you learn from each spoiled negative how to avoid a similar failure in the future, you will soon be making negatives that will need no “doctoring.” When you have made a failure, the most important thing is to learn the cause. The improvement of that particular negative is of secondary importance.
Over- and underexposure are among the most common causes of failure. I have already told you how to detect these mistakes during development; but if they escape your attention then, there is a still more simple way by which they may be recognized after the negative is dry. Hold a black cloth or paper behind the negative, and look at it by reflected light. If it shows a positive on the film side only, the negative has been undertimed. When only the glass side shows a positive, it has been overtimed. But if a positive can be seen on neither side or on both sides, the exposure has been about right.
If a plate is known to be undertimed before development begins, the normal developer should be diluted with an equal quantity of water. This will greatly lengthen the time of development; but it will soften the contrast, and bring out more detail in the shadows. Under this treatment an underexposure will come out better than when treated with normal developer; but, generally speaking, the mistake is a fatal one.
When the plate is known to be overtimed, the developer should be concentrated. Equal parts of our “standard” developing solution and water, with the addition of four drops of a ten-per-cent solution of bromide of potassium, or of a fifteen-per-cent solution of chloride of sodium (common salt), to each ounce of developer will compensate for a pretty bad overexposure. After an overtimed plate has been developed, it is past all hope of improvement.
When a negative is thin and weak, but full of detail in both high-lights and shadows, it is underdeveloped. This fault may be corrected by intensification. Intensifiers may be bought at any stock house, and some manufacturers send out intensifier formulas with their plates; but about the best one, and that most used, is the mercuric bath given below:—
Bichloride of mercury, 1 dram Bromide of potassium, ½ ounce Water, 4 ounces
Mercury dissolves slowly, so it is best to keep this solution on hand. However, you should keep it out of the way; for bichloride of mercury is another name for corrosive sublimate,—a deadly poison.
The negatives to be intensified should be placed in the miscellaneous tray, and the mercuric solution poured over them. A white deposit will at once begin to appear on the surface of the film. If the negatives require much intensification, they should be left in the solution until this action ceases. Then pour off the intensifier, and pour over the plates a few ounces of a ten-per-cent solution of sulphite of soda. This will blacken the white mercuric deposit, after which the plates may be washed and dried just as after fixing.
Sometimes a negative will be so dense that in all but a strong transmitted light it will appear quite black, even in the shadows. This is caused by overdevelopment, and may be corrected by reduction.
Ferricyanide of potassium, ¼ ounce Water, 4 ounces
This solution also is poison, and the bottle should be so labeled. Light has a tendency to decompose this solution, so it is well to keep the bottle wrapped in black or dark-brown paper. To make a reducer, add one-half dram of this solution, and a lump of hypo. about twice the size of a pea, to eight ounces of water. Watch the plate closely, or you may get it too thin. When sufficiently reduced, remove the negative, and wash it as you would after fixing.
Sometimes you will see dark streaks radiating from one corner or edge of the plate, and extending across its entire surface. Such plates have been “light-struck,” and nothing can be done to improve them. In some way a ray of light has reached the plate without coming through the lens at the time of exposure. The trouble is generally caused by a leaky plate-holder.
When there is a leak in the plate-holder, so situated that diffused instead of direct light reaches the plate, it will “fog” the negative. Then the entire image will be veiled and indistinct, just as the subject would appear on a foggy day. An unsuitable developing light, or a developer containing too much alkali, may also cause fog.
“Pin holes”—little spots of clear glass—are usually caused by specks of dust on the plate during exposure. To avoid them, the plate should be carefully dusted when the holders are loaded. Pin holes may be spotted out with some opaque water-color carried on a fine-pointed brush. If the spots are small, and you are deft-fingered, they may be lightly touched with pen and ink, but the water-color is better.
When a negative shows too much contrast,—black high-lights and shadows of clear glass,—the trouble may have been caused either by underexposure or by too many contrasting lights on your subject. When it is necessary to photograph anything in contrasting lights, it is advisable to overtime the plate, and develop with normal developer. This plan will reduce the contrast, and often yields good results where a normal exposure will fail.
In photography it is easier and better to avoid mistakes than to correct them. So in our Christian experience. If we make a mistake or commit a sin, it may be rectified or forgiven; but how much better not to sin! “My little children, these things write I unto you, that ye sin not. And if any man sin, we have an Advocate with the Father, Jesus Christ the righteous.” Oh, wonderful love! A power has been provided to keep us from sin; but if we let go that power, and fall, an Advocate stands ready to plead our cause, and bear our sins himself. J. EDGAR ROSS.