How to Make Things — No. 2
W. S. CHAPMAN
A BOY should have a workshop. Without a place in which to “tinker” he is robbed of half the enjoyment of being a boy. So if you have no such place and there is a corner anywhere that could be given to you, say in the woodshed or some outbuilding, ask for it, and construct a “shop.” In it you can spend many a happy hour at this tinkering, and best of all, be kept out of unwholesome company and much mischief, while no doubt making some things really worth while.
Tools Needed
A crosscut saw, a brass-bound two-foot rule, and a square of some kind will now be required. If you are able to buy a carpenter’s square buy a good one. Under no consideration be satisfied with a cheap iron square. They are never accurate; they will bend and twist and get out of shape and are unreliable as to measurements, so that good work is not possible with their use. Wait until you can afford to buy the very best you can find, for next in importance to the hammer or hatchet comes the square. You will need a six-inch try-square, so buy one and it will answer for all that is needed until you come to build a workshop.
The Workbench
A bench needs to be solid and not easily moved out of place, hence must be constructed of heavy material. As you are not yet capable of working in heavy hardwood, your table must be made of pine. If your shop has a window (or you can put in one), then build the bench under the window and fasten the back to the wall. This will make it almost immovable.
The End Pieces and Legs
Procure two fairly good-sized drygoods boxes and place them about six feet apart. Lay upon them your piece of studding. This comes two inches thick and four inches wide, that is, this is the size when sawed out of the log, but afterward the pieces are run through a planer, which takes off a shaving that reduces the size about a fourth of an inch in width and thickness. In some classes of work it is important to remember this, but in coarse work, like the building of this bench, it is not necessary to make allowance for this loss in size. Planing this way is called “dressing” the lumber, and the finished product is called “dressed lumber.”
In building this bench it is not necessary that the ends of the pieces should all be absolutely square, but it pays to strive to be accurate in even the simplest details, so always try to square the ends. Place the square on the studding about two or three inches from the end, hold it firmly against the side, and draw with a carpenter’s pencil a straight line across the top. Next place the point of the pencil on the line at the inside edge near to you, tip the square over so that the blade hangs down the side, and slide it up to the pencil point; then holding the square steady, draw a line down the side of the studding. Do the same on the other side, and then you will have three lines—on the top and each side—to guide you in sawing. To saw straight, remember to keep your saw upright and at right angles to the material through which you are sawing. Accuracy in sawing is of the utmost importance, and it should be your aim to become a good sawyer. You will never do fine work until you become accurate in this particular, so practice, practice, practice, until you are expert.
Having now a “square end” in your studding, with your two-foot rule, or a steel square if you have one, measure off exactly 5 feet 10 inches, and before sawing it off, square the end as you did before. This piece is now to be spiked to the wall with the top at precisely 28 inches from the floor. In doing this use about four spikes.
You will now need two end pieces of one-inch stuff to be nailed to this wall piece, on which the top of the table is to rest. The other ends of these pieces are to be nailed to the front legs. Before cutting off these pieces you must decide how wide a table top you are to have. The front board should be the widest, as you will do most of your work on it, the back part being used mainly for tools and pieces of boards that you are using in your work.
A board 12 inches wide would be preferable, but as wide boards are expensive it had better be 10 inches, so a board 12 feet long when cut in two will give you the two front boards, and a six-foot piece 6 inches wide will make the back. This will give you a table top 26 inches wide, an ample width for all the work you are likely to undertake. Don’t forget to square the ends of all these boards. As the table top is to be 26 inches wide, the end pieces are to be cut that width, one for each end.
These end pieces must be nailed to the legs before being attached to the wall piece, as they are to be fastened to the legs, which are to be made of studding. As the wall piece is just 28 inches from the floor, the legs must be that length so that they will reach to the top of the wall piece. Remember that the apron is to be nailed to the legs, so that its face comes even, or flush, with the end of the side pieces. Therefore mark off one inch from the end on the end pieces and place the leg back of that mark. Have the wide side toward you, nailing through the side that is two inches wide. Then, too, remember to put the legs inside the pieces you nail them to, so that the board will be outside at each leg.
Lay the leg down on the boxes with the narrow edge up and put the end piece over it so that the side will come to the mark. Use five nails and drive one at each corner and one in the middle, not all the way through. Better do this before attaching the legs. When you think that you have the end piece in proper position, drive one of the corner nails fully, then take your square and lay it on the edge of the leg so that its other blade will be up against the edge of the end piece. If you cannot see light through the places where the blades touch the wood, drive another nail home, and try the square a second time. If all is right, drive all the nails, but if you can see above the blades any streak of light, pull out the second nail and try again until you do get them to square up.
Bracing
Next fasten the end pieces to the wall piece, and nail on the front top board, then the apron to the legs and the end pieces. After this nail the edge of the front top board firmly to the edge of the apron with nails driven about six inches apart. Now finish the table top by nailing on the other two boards. The purpose of having an apron will be explained farther along, as will also that of the bench vise.
If the bench is well put together it should need nop. 11 bracing, but it will be safe to nail on strips from the legs, an inch or two from the bottom, diagonally to the wall strips near the wall. Six feet of strips will be ample for the purpose. If you are expert at toenailing nails into wood, fasten the legs that way to the floor. If you do not understand this way of nailing, ask your father to do it for you, or better perhaps, ask some carpenter to fasten them for you. You may learn something new from him. Be always on the watch to learn from carpenters at work.
The Lumber Bill
From the beginning you should practice getting out lumber bills. A lumber bill covering all the lumber that will be needed for your work is to be carried to the lumber dealer, and from it he selects in his yard what you want and delivers it at your house or shop.
The contents of lumber, that is, the number of board feet, or running, or linear, feet in a certain quantity of lumber, is ascertained by multiplying the number of pieces by the thickness, width, and length, finally dividing by 12 to reduce the sum to feet. For instance:
One piece of studding twelve feet long would be expressed as follows: One piece 2 × 4 × 12 = 96 ÷ 12 = 8 running feet.
An inch board 12 feet long would be expressed: One piece 1 × 12 × 12 = 144 ÷ 12 = 12 feet.
A plank 2 inches thick would be just twice the number of feet of a board 1 inch thick, and would be expressed this way: One piece 2 × 12 × 12 = 288 ÷ 12 = 24 feet.
In making out a bill for the lumber dealer it is best to lump all the pieces of a kind, as all 2 × 4’s, all 1-inch dressed boards, that all pieces of the same thickness and same width may be together.
You will need three pieces of studding, one 5 feet 10 inches, and two 2 feet 4 inches each, making 10 feet 6 inches in all. But as lumber does not come in this length, we will call the total 12 feet. So of the boards, you will call for three boards 10 inches wide and 6 feet long. In the bill it will be one board 18 feet long, one board 6 inches wide and 6 feet long, and one 5 inches wide and 6 feet long, so the total bill would look like this:
One piece 2 × 4 × 12.
One piece 1 × 5 × 6, dressed.
One piece 1 × 10 × 18, dressed.
One piece 1 × 6 × 6, dressed.
Leave the lumber dealer to figure out the total his way, as each has some notion in doing it. All but the first item in the bill is what is called dressed lumber, that is, has been planed down by machinery at the mill, generally on both sides, and is what will be sent you. Unplaned lumber is called rough lumber. Studding comes under this head even though it is now usually planed. It formerly was delivered in the rough, so retains its name.
Any boy who may have difficulty in understanding the making of a bill of lumber from what is written, may write me concerning his trouble, and I shall endeavor to set him right. Address me at St. Petersburg, Florida.