AdventAI

Purification and Analysis of Water

By Noah Baharian

From The Youth’s Instructor, Vol. 65, No. 50., December 11, 1917

WATER is one of the most familiar of chemical substances. Besides covering more than three fourths of the earth’s surface, it enters into the composition of organic matter. Without it animal life is impossible. It is therefore of the greatest importance that we should be able to ascertain the purity of the water we use and know how to purify it.

Water in nature holds many substances. Rain water, though considered the purest, on heating gives air bubbles and ammonium nitrate, besides the dust mixed with it. In well waters we find compounds of calcium and magnesium, iron, bicarbonates, and carbon dioxide. It often contains organic matter from decomposing organic matter teeming with bacteria of putrefaction.

Impurities of water may be divided into two classes,—dissolved and suspended matter. Absolutely pure water cannot exist on account of the great solvent action of water. Even glass dissolves in water to a noticeable extent. Suspended matter can be removed by filtration. The tiny pores of an undersized paper let the liquid go through, but retain the solid matter. Gravel beds are used on a larger scale. Porcelain filters may be had for family use. Dissolved substances may be conveniently removed by distillation and condensation in cold platinum or tin pipes.

To determine the total amount of solids in water, evaporate about 500 cubic centimeters of the water in a weighed platinum or porcelain dish. The water should not be boiled, because some of the solids may be volatile. A double-boiler water bath is the best. When about dry, the dish is transferred to a hot-air oven of 100° F. After half an hour the water will have entirely disappeared. The dish and its contents are then weighed. The increase in weight is the amount of total solids found. The dish may now be held over a strong flame. If it chars and blackens, organic matter must be present. Water containing enough organic matter to cause this charring is unfit for drinking.

When water contains certain salts, it is called “hard.” On adding soap, these salts combine with the fatty acid of the soap, and produce an insoluble, dirty-looking precipitate. If the water contains only bicarbonates, the hardness is said to be temporary. Simple boiling will change the soluble bicarbonate to insoluble carbonates. The water is thus softened. Sulphates or chlorides do not precipitate on boiling, hence water containing them is said to be permanently hard. The usual way to indicate the amount of hardness is to note the quantity of a standard soap solution necessary to produce a permanent lather. Good potable waters show no permanent hardness and very little temporary hardness.

(Concluded on page eight)p. 3

(Concluded from page two)

Chlorine will reach water generally through sewage. It is therefore important to know the amount of chlorine present. To detect chlorine, add a few drops of silver nitrate solution. A cloudy precipitate of silver chloride will be formed which will in time darken. To find the amount of chlorine, titration is used, the amount of silver nitrate used to precipitate all the chlorine present determining the amount of chlorine in the water.

Nitrates are formed from nitrogen coming usually from the oxidation of organic matter. Though harmless in themselves, they indicate contamination with organic matter. A delicate test is to dry some of the water to be tested, then add a few drops of phenol-sulphonic acid. After being neutralized with ammonia, the nitrates present will form a yellow precipitate of ammonium picrate.

The presence of nitrates is still more dangerous, because it indicates recent contamination with nitrogenous matter. Its presence is to be determined by acidulating the water and adding a solution of a mixture of aniline sulphonic acid and α-naphthylamine hydrochloride. A pink color will develop with nitrites.

Water always contains some ammonia. A slight amount is not only harmless but even healthful. A larger amount, however, is deleterious. Very minute traces of ammonia can be detected by adding Nessler’s Reagent. A dark brown indicates ammonia.

It is often hard to interpret the results of an analysis. This is due to the fact that many of the substances found are harmless in themselves, and only indicate danger of contamination from their source. The best way is to compare the sample with the normal character of the waters of the region. Any deviation from this should arouse suspicion.

NOAH BAHARIAN.