How to Make Things — No. 3
The height of the worktable has been given as 29 inches,—legs, 28 inches; top, 1 inch,—as that height will be best for the general height of boys from eight to sixteen years of age. The lower you have to bend in working, the more fatiguing it becomes.
If you stand erect and bend the forearm into a horizontal position and then measure from the floor to the under side of the arm, you will have the proper height for the table top. If you decide upon any other height than the one given, be sure to make the proper allowances in the legs and the height of the piece nailed to the wall.
Most carpenters in building a workbench allow the top board and the apron board to project some six inches beyond the side pieces. There is no very good reason why this allowance should be made, and in a small room it is a decided disadvantage.
We need now to consider the furnishings of the workbench. These are a bench vise, a bench stop, a bench hook, and a miter box. There are two styles of bench vise, the old wooden one and the more modern iron vise. My preference goes to the old style. You need to talk with the hardware merchant, and then select the style which appeals to you the strongest.
If not convenient to purchase the metal stop at the store, you can get along nicely for a time by using two screws placed parallel with each other and about three inches apart. These screwed into the table top can be raised or lowered to suit the board you may be working on, only you must exercise great care that the screws are kept low enough to be out of the way of the plane iron. When planing, especially with the jack plane, an eighth of an inch can be planed off quite rapidly.
You will need another stop, sometimes called a “bird’s mouth.” This you can make yourself. It is a piece of board about four by six inches with a V-shaped cut-out in the center, reaching back about one and one-half inches, being the same width at the front. This you are to nail onto the top about two inches from the metal stop. It is used to hold a board steady when dressing its edge.p. 9
The real bench stop is a metal plug, with a serrated or notched top piece, set in a case in which it slides up and down. This case is to be mortised into the table top on a line with the bench vise and about eight or ten inches from the front. The plug is raised or lowered to suit the height of the wood you are working on, the end of the board being held by the serrated teeth of the stop.
Another piece of bench furniture of great practical value is called the bench hook. This is a piece of inch board about ten by twelve inches, with strips nailed or screwed upon it, the strips being about two inches wide, the upper strip two inches thick and the lower an inch thick. The two-inch strip is fastened on the edge of the upper side of the board and the inch strip at the other edge of the under or reverse side. This under or narrow strip is to be placed against the edge of the table when in use, and any article to be sawed, or otherwise worked with, is held against the upper strip, which acts as a stop to hold it, while sawing with a backsaw, for instance, or when mitering molding for picture frames, etc. It is used, also, as a miter box for small work, and therefore the upper strip should be mitered like a miter box, with a right-angle cut in the center and diagonal cuts each side for right and left diagonals at 45°; so, before nailing the strip to the board, measure off the center and draw a line across the top. Measure halfway between that line and each end and make a mark at the edge of the board, but do not draw any lines, as these lines are to be drawn with a bevel square or with the carpenter’s square.
To explain a bevel square and to show you how it is used would take at least a column of the INSTRUCTOR space. If you can interest either your hardware man or a good carpenter, he can show you in ten minutes more than I could explain in a column, and to much better advantage. After the stop is marked, nail it to the edge of the board quite firmly, as it has to endure much strain. Put four nails between each of the marks and two or three at the ends, then saw the strip all the way through over each of the three lines, so making a miter box with a right angle and a right and left 45° angle, which is about all a boy carpenter is likely to need.
You cannot, alone, place the bench vise in position. I advise you to employ a first-class carpenter, as much depends upon the good workmanship used in this helper, nor will you be able to fit in the metal stop, as it is nice work with chisels which you will not be familiar with. If the work is not nicely done, it gives the table top a bad appearance. Possibly it would be better to get along with one of the homemade stops for a time, only “makeshifts” are always liable to lead to shiftlessness in other ways. Resolve to do good work every time, and let the work wait until you can afford to buy the proper tools rather than slight anything that you undertake.
In this connection — building and fitting up a workbench — let me strongly advise you to visit carpenter’s shops and critically examine all the benches you come across. You will find that they vary greatly, many being a disgrace to the men who use them. But occasionally you will come across a well-built table. Look it over carefully, and if possible, talk with its owner. The chances are that you will see a man who has made a success and is a very busy individual. If you could get invited to call on him in the evening after he has had a good supper, he might prove a gold mine of practical information and a real helper. He might become very enthusiastic over your efforts and prove a good friend. Anyway, pick up all the information you can while visiting shops, and especially notice how many holes are bored in the apron of the workbenches, in which a movable plug is used on which to rest boards that are being jointed or having their edges dressed.
Then, too, notice how the buildings are put together, that is, if they are mere one-story shops; how the sills are laid; how heavy they are and how put together; how the corner posts are treated; how the upper joists are laid on the plates and what they are made of; how the rafters rest on the plates and how the tongues are cut; etc. Some of these words you may not understand; please go to the dictionary or ask your father. Get into the habit of searching out for yourself; for information gained in this way will “stick,” and in after-years you will be thankful that you acquired the habit.
You can, if you think best, try to make a large miter box, under instruction of a good mechanic; but you will not need one for some time, and, possibly, you might feel quite proud some day if, after more experience, you built one all by yourself, picking up the ideas from observation and by asking questions of patient workmen.
W. S. CHAPMAN.