BLUE PRINTS

5%

Review and Herald Publishing Company · Battle Creek, Mich. · Jun 7, 1900

FromThe Youth’s Instructor, Vol. 48, No. 23.

Read the full edition

BLUE PRINTS

THE blue-print process is very cheap, very simple, and consequently very much despised. But for many subjects there is no prettier printing process known to photographic science. Of course if one uses blue prints exclusively, for all subjects, he may in time find the sameness of their tone monotonous; but a very simple process of bleaching and redeveloping will turn the blue to a brown, or even to a deep black.
Blue-print paper may be bought ready for the printing-frame; but its cost is not much below that of silver print-out paper. It requires a somewhat longer exposure than gelatin paper, and it does not show as clearly defined an image; but a little practice will enable you readily to tell when it has been printed enough.
After printing, the paper is simply washed until it no longer colors the water. Five minutes is sufficient for this if the print is kept constantly in motion. The picture is then ready to mount, or to dry without toning, fixing, or further washing. Quite simple, isn’t it?
The preparation of blue-print paper is almost as simple as its printing. Any paper may be used, but of course the regular photographic paper is best. Good, smooth, unruled writing-paper answers the purpose well, however. Bristol-board and pen-and-ink drawing-paper are also excellent, especially if the prints are to be kept unmounted.
The sensitizing solution is made as follows:—
Ingredient Amount
Citrate of iron and ammonia 1¾ ounces
Water 8 ounces
Ferricyanide of potassium 1¼ ounces
Water 8 ounces
These solutions will keep separately, but they should be mixed only for immediate use.
Take equal parts of each, and float, or immerse, the paper for three minutes; then hang it up to dry in the dark. Another method of coating the paper is to swab the surface with the solution. Many prefer this method; so I will describe it in detail.
Take a half-inch board, three inches wide by eight inches long, and cut it out to the shape of the handle of a flat paint-brush. Then wrap a long strip of soft, white muslin about three inches wide around the wide end of this stick, until you have quite a thick pad. Wind a string several times around the muslin, and tie it firmly in place. You will then have a swab that will serve as well as a camel’s-hair brush, for which you would pay a dollar.
Provide a board somewhat larger than the paper to be coated, and fasten the paper to it by placing a drawing-tack or a pin at each corner. Stand the board on end in a tray containing a small quantity of the sensitizing solution, and hold it at an angle of forty-five degrees with one hand, while with the swab in the other you brush the solution over the surface of the paper with a quick up-and-down motion. Turn the board on its side, and repeat the operation, so that the marks of the swab will be in both directions of the paper,—up and down and across.
The paper will look streaked, but that will not matter if the surface has all been covered. The streaks will disappear in the final washing. Two or three dozen sheets of paper can be coated in this manner in half an hour.
Blue-print paper keeps well, but it must, of course, be kept in the dark. A number of large sheets may be sensitized at one time, and then cut, when dry, to the required size, and stored away until needed.
The natural tone of the blue-print gives quite a pleasing effect to most views. The only reason that it is held in such contempt is that the process is so cheap and simple. If you dislike the blue tone, it may be changed to a pretty brown color by the following process: Immerse the prints in a bleaching-bath composed of one part aqua ammonia to ten parts water, until the image is faded out to a pale yellow. Wash through three or four changes of water, and immerse in the following solution:—
Ingredient Amount
Water 10 ounces
Tannic acid 2 ounces
This bath will slowly redevelop the image to a brown tone.
This formula has been published again and again. I have met people who have used it, and I have seen prints it has produced. The time necessary to redevelop the image in the acid bath is said to be about twelve hours. I must confess that I never had the patience to try it. I did look for a short cut, however, and found it in my plate-developer.
The formula used was the one for eikonogen-hydrochinon developer, as given in the article on Plates and Developer. No doubt other developers would answer equally well, but I have never tried them.
In this developer the faded image comes up clear and strong in a few minutes, losing nothing but the blue color, which has been exchanged for a brown that resembles an old engraving. Personally, I prefer the blue prints, but as tastes differ, the reader should try this method.
J. EDGAR ROSS.