TRIMMING AND MOUNTING

10%

Review and Herald Publishing Company · Battle Creek, Mich. · May 3, 1900

FromThe Youth’s Instructor, Vol. 48, No. 18.

Read the full edition

TRIMMING AND MOUNTING

My favorite mounts are plain cardboard of some dark color, such as steel-gray or dark mode. Embossed mounts are very pretty when the picture fits them, but it is often difficult to get an embossed mount to fit a picture without having it made to order. Of course it is easy enough to make the picture fit the mount; and when an embossed mount is used, one is often tempted to trim the print down to fit it. This I regard the strongest point in favor of the plain cardboard.
The mount should be considerably larger than the photograph. For five-by-seven-inch pictures, or any smaller size, there should be a margin of at least one inch all around the print. A five-by-seven-inch picture would thus require a seven-by-nine-inch mount. If the print is larger than this, it should have more margin; but this is a matter that must be regulated by individual taste. If a print has been trimmed down much below the usual size, it may still be mounted on the regular size of card, and will simply have a wider margin.
I prefer to trim my prints before toning them; but if you are undecided as to how they should be trimmed, it may be well to tone them first, and dry them unmounted. They may then be exposed to the light indefinitely, and will bear much rougher handling than before they are toned. Never try to trim prints while they are wet. If you do, you will be sure to get ragged edges. You can buy a trimming-knife for three or four dollars; but a pane of glass, an old penknife, and an iron straightedge, or even a common wooden ruler, will do just as well.
Lay the print, face up, on the glass, and place the ruler along the line where you wish to cut. Then with a firm, even pressure draw the knife quickly along the edge of the ruler, and the paper will be cut as smoothly and evenly as any trimming-machine could cut it.
Do not think that what you trim off your print is wasted. Very often a rather poor photograph may be turned into an excellent picture by a little judicious trimming. Often there is too much empty foreground, or too great an expanse of clear sky, or an unsightly object at one end of the print. These should be fearlessly cut away until everything that can be spared from the picture without detracting from its artistic merit has been removed. I have one six-and-one-half-by-eight-and-one-half-inch negative that gives me a print, when properly trimmed, measuring only one and three fourths by six inches. I regard it one of my best negatives; but if it should be printed full size, the picture would not be worth a card to mount it on.
If the prints have been dried, they must be soaked in water a few minutes before you undertake to mount them. Take them from the water one at a time, and pile them, face downward, on a piece of glass, oilcloth, or even common wrapping-paper. Do not try to place them evenly, or you will have a hard time to separate them again. When they are piled up without special care, they will usually be quite uneven, and then there will be no difficulty in picking them up separately. Press out as much of the water as possible from the pile of prints, and wipe it up with a blotter or towel.
Almost any kind of adhesive paste may be used in mounting. The one most common is made by adding cornstarch or white flour, braided smooth in a little cold water, to boiling water. It is difficult to give the exact proportion of starch and water, but sufficient starch should be used to make the paste about the consistency of thick cream. When it gets cold, it will be much more firm. It is better to have it too thick than too thin, as it can be reduced to the desired consistency by the addition of a little water. This paste may be spread with a cloth; but a regular paste-brush will cost only ten or fifteen cents.
Spread the paste smoothly and evenly over the entire back of the print. Do not use too much, or when you roll down the print, it will be pressed out at the edges on the margin of the mount. If any hairs from the paste-brush, or any other particles of foreign matter, adhere to the print after the paste has been spread, they may be removed with the point of a knife. Slip the knife point under one corner of the print, and lift it up until you can get hold of it with the thumb and forefinger of the free hand. It may then be lifted from the pile, and placed in the proper position on the mount. Cover the print with a blotter or three or four thicknesses of soft cloth, and roll down with a print-roller. You can buy a fairly good print-roller for a dollar; but an ordinary rolling-pin will answer the purpose much better, and if you can't borrow one from the pantry, you can buy one for ten cents. If there is any paste on the face of the print or mount, it may be wiped off with a damp cloth or sponge. Then the picture may be left, face up, to dry, while you proceed to mount the next one.
J. Edgar Ross.