In and About San Francisco—IV
By J. Edgar Ross
The Largest Mint in the World
No one who visits San Francisco should fail to see the mint, which stands in the very heart of the business district. The building itself is well worth looking at, even if one were permitted to see no more than the outside; but there is no red tape to be unwound in order that one may be conducted through the San Francisco mint. On the contrary, the guides, who are appointed for that purpose, receive all comers with the greatest courtesy, and treat them as if they were guests who had conferred a special favor by calling. No pains is spared to make the visitors' stay both pleasant and instructive. On leaving the spacious reception room, one is taken down a back stairway, and through a dark passage to the door of a vault, which, he is informed, contains so many hundred million silver dollars that it fairly takes his breath away. These are idle coins, represented in the business world by silver certificates, and the vault is never opened except to add more to the store, or to count the coin already there. Then the conductor leads the nation's guest through the fire-room, where grimy men are shoveling coal into furnaces beneath huge boilers, and upon another stairway to the melting department. Here is where the gold is first taken when it is received at the mint, to be melted and cast into bricks before it is assayed to determine its value. Each consignment of gold must be melted separately. When I visited this department, I was so fortunate as to see two great pots removed from the furnace, and the molten gold that they contained poured into molds to solidify. This required scarcely a minute, and then two red-hot gold bricks were unceremoniously dumped out upon an iron truck, and wheeled to another part of the room to be cooled in a tank of water. The smaller of these bricks was about the size of an ordinary building brick; yet its value, the conductor informed me, was approximately twenty thousand dollars. The ingot room is next seen. Here the gold bricks are melted, mixed with the necessary amount of copper alloy, and cast into ingots about twelve inches in length and an inch thick. Great stacks of these yellow bars are piled up beside the furnaces. Measure them off into twenty-dollar pieces as near as a mental calculation will allow, and you will probably conclude that there are twenty-five or thirty coins in each; but the conductor will inform you that they contain eleven hundred dollars' worth of gold. When the metal comes from the ingot room, it is too brittle to stand the great pressure necessary to mold it into coins, so it must be softened. This is accomplished by placing the ingots in long copper tubes, which are hermetically sealed, and placed in an oven, where the temperature is slightly below the melting point of the metal. When the necessary time has elapsed, these tubes are removed, and plunged into a tank of boiling water to cool. This process is called “annealing;” and it is to the annealing room that the visitor is conducted after leaving the ingot department. Next he is shown as fine a specimen of machinery as one often sees—a forty-thousand-dollar steam engine, every part of which is polished like one of the new silver dollars that it furnishes the power to make. It was a great surprise to me to learn that this engine furnished only one hundred and fifty horse-power, and that that was sufficient to run all the machinery in the mint; for this is the largest mint in the world, with a capacity of four hundred and fifty thousand dollars an hour when only gold is being coined—more gold than the world produces in the same time. The desire of the conductor seems to be to follow the gold in its journey through the various departments till it comes forth a finished coin; so the visitor is next shown the rolling machines. The ingots are passed through these machines till they are rolled to the thickness of the coin to be cut from them. If twenty-dollar pieces are to be made, it is necessary to pass them through about fifteen times; and the pressure is so great that the rollers, though made of the finest steel and as large as a man's body, are sometimes snapped off like pipe-stems. The ingot comes from these machines about seven feet in length, and is then ready to be cut. In the cutting room the visitor sees these long bars of bright-yellow metal being passed into a machine that punches twenty-dollar pieces from them as easily, as smoothly, and far more rapidly, than a conductor punches holes in the thin cardboard of a railroad ticket. Beside this machine sits a man who weighs a coin from each ingot that is cut, to make sure that it is approximately of the right size. This is not the final test for weight, however, as each coin is weighed separately before it is stamped. The room where weighing is carried on is closed to visitors, for what reason the guide does not explain. He tells you, however, that at a long table in that room, fifty women are seated, each with a delicate pair of balances before her, and a small file in her hand. If a coin is half a grain too light, it is rejected and sent back to the ingot room to be remelted. If it is half a grain too heavy, it is filed down to the required weight. The regulations of the mint require that the carpet of this room shall be burned every four years to recover the gold and silver that it contains. The last carpet that was burned contained four thousand five hundred and fifty-four dollars in gold alone. The last room to which the visitor is admitted is the press-room. Here he sees the smooth, round pieces of metal being fed to a press from which they come forth stamped on both sides—bright, glittering coins. The pressure required to stamp a coin is one hundred tons, and the capacity of each of the five presses is six thousand coins an hour. J. EDGAR ROSS.